Wheel offset and width calculator

See how far a wheel moves outwards and how the space on the inside changes. Compare width, offset and spacers in one drawing.

Current wheel
Spacer
New wheel
Spacer
What changes?

Wheel position comparison

Outer edge
Inner clearance
Track width changewhen both wheels are changed equally

Wheel cross-section and position

Current wheelNew wheel
Wheel cross-section and positionWheel width and spacer thickness follow the entered dimensions. Grey suspension parts are for orientation only. The drawing cannot tell you the actual gap to the suspension or wheel arch on your car.

Calculation details

Width and offset work together

What causes this change?

What causes this change?Width and offset work together
ParameterCurrent wheelNew wheel

Notes

How to read the drawing. Wheel width and spacer thickness follow the entered dimensions. Grey suspension parts are for orientation only. The drawing cannot tell you the actual gap to the suspension or wheel arch on your car.

Which width to enter. Use the width marked on the wheel, for example 7.5J. This is measured between the tyre bead seats. The overall metal rim is wider. The calculated movement also applies to the outer edges if both wheels have the same flange projection.

Before fitting. Check the vehicle and wheel manufacturers’ requirements: wheel size, bolt pattern (PCD), centre bore, bolts or nuts and load rating. Check space for brakes and tyres too. Position changes alone do not confirm that a wheel will fit.

How to compare wheel offsets

01

Find the markings

Look for width and offset on the wheel, for example 7.5J × 17 ET45. Enter 7.5 and 45.

02

Enter the new size

Enter the new wheel’s width and offset. If you use spacers, enter the thickness per wheel for both setups.

03

Read the drawing

Compare the outer edge movement and the change in inner clearance.

04

Save your comparison

Print the summary or save it as a PDF. Use the tyre size calculator for changes in tyre diameter.

Three separate effects

A lower offset does not tell the whole story: a wider wheel also takes up more space on the inside.

Width

One extra inch is 25.4 mm. At the same offset, the rim extends 12.7 mm further on each side.

Offset (ET)

Reducing offset by 10 mm moves a wheel of the same width 10 mm outwards.

Spacer

A 10 mm spacer moves the wheel 10 mm outwards. Adding the same spacer on both sides increases track width by 20 mm.

How wheel width and offset changes are calculated

Both wheels are compared relative to the same hub mounting plane. Width in inches is multiplied by 25.4 to give millimetres. Spacers are included by reducing the effective offset. E = marked ET − spacer thickness

This is a geometric equivalent. A spacer does not change the offset stamped on the wheel.

Outer edge movement

Δ outer = (W₂ − W₁) / 2 + E₁ − E₂

A positive result means further outwards.

Inner clearance change

Δ clearance = −(W₂ − W₁) / 2 + E₁ − E₂

A positive result means more room on the inside.

W₁ and W₂ are the current and new widths in millimetres; E₁ and E₂ are the effective offsets. Track width change = 2 × (E₁ − E₂) when both wheels on the axle are changed equally. Increasing width alone does not change track width if the wheel centre stays in the same place.

Example: 7.5J ET45 versus 8.5J ET35

Without spacers, width increases by 25.4 mm, adding 12.7 mm on each side. Offset decreases by 10 mm. The outer edge moves 22.7 mm outwards and inner clearance decreases by 2.7 mm. Changing both wheels equally increases track width by 20 mm.

What the drawing does not include

Nominal width is not the overall metal rim width. Flanges and spoke shapes vary by model. A tyre can be wider than its rim, and available space changes as the steering and suspension move. This tool compares wheel position changes, not actual clearance on a particular car. Check tyre diameter, profile and theoretical speedometer changes with the tyre size calculator.

Sources explaining the dimensions

Frequently asked questions about wheel offset

What is wheel offset (ET)?

Offset is the distance in millimetres between the wheel’s centre plane and its hub mounting face. Positive offset places the mounting face closer to the outside. At the same width, a lower offset moves the wheel outwards.

What is the difference between ET35 and ET45?

With the same width and spacers, ET35 sits 10 mm further out than ET45. The outer edge moves out by 10 mm and inner clearance increases by 10 mm. Changing both wheels on an axle equally increases track width by 20 mm.

How does a wider wheel affect suspension clearance?

If offset and spacers stay the same, extra width is split equally between the two sides. Going from 7.5 to 8.5 inches moves the outer edge out by 12.7 mm and reduces inner clearance by 12.7 mm.

How does a spacer change wheel position?

A spacer moves the whole wheel out by its thickness. Effective offset equals marked ET minus spacer thickness. ET45 with a 10 mm spacer has the same geometric position as an equally wide ET35 wheel without a spacer. Enter thickness per wheel, not the total for both sides.

What does 8.5J × 18 ET35 mean?

8.5 is the nominal width in inches, J identifies the flange profile, 18 is the nominal diameter in inches and ET35 is a 35 mm offset. Enter width 8.5 and offset 35 here. Diameter alone does not change these horizontal movements; use the tyre calculator for diameter comparisons.

Does the calculator confirm that a wheel will fit my car?

No. Fitment also depends on bolt pattern, centre bore, fixings, load rating, spoke and brake calliper shapes, tyres and clearance during steering and suspension movement. Follow the vehicle and wheel manufacturers’ requirements.

Why is nominal width different from overall rim width?

Nominal width is measured between the bead seats rather than the outermost metal edges. The calculation assumes equal flange projection on both wheels. Different flange profiles can change the actual edge movement. The drawing does not reproduce a specific wheel profile.

Can I compare negative offsets and wheels without spacers?

Yes. Enter a negative ET if needed and 0 mm for no spacer. The tool accepts widths of 3–16 inches, offsets of −100 to +100 mm and spacers of 0–50 mm per wheel, with up to two decimal places. These are input limits, not an approved fitment list.

Are my dimensions saved or sent to a server?

Dimensions are processed in your browser and are not sent to a server for calculation. Print / PDF opens your browser’s print dialog, where you can save a PDF. The site’s general analytics and cookie settings still apply.